CPU0: P2020, Version: 2.1, (0x80e20021)
Core: E500, Version: 5.1, (0x80211051)
Clock Configuration:
CPU0:800 MHz, CPU1:800 MHz,
CCB:400 MHz,
DDR:333.333 MHz (666.667 MT/s data rate) (Asynchronous), LBC:25 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Board: Celestica Redstone (cpld_ver: 1.7)
I2C: ready
DRAM: 2 GiB (DDR3, 64-bit, CL=6, ECC on)
Flash: 64 MiB
L2: 512 KB enabled
NAND: 1024 MiB
EEPROM: TlvInfo v1 len=112
PCIe1: Root Complex, x2, regs @ 0xffe0a000
01:00.0 - 14e4:b842 - Network controller
PCIe1: Bus 00 - 01
In: serial
Out: serial
Err: serial
Net: eTSEC2 is in sgmii mode.
eth0 [PRIME]
Hit any key to stop autoboot: 3 2 1 0
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at ec000074 ...
Image Name: System for celp2020
Image Type: PowerPC Linux Multi-File Image (gzip compressed)
Data Size: 23160796 Bytes = 22.1 MiB
Load Address: 00000000
Entry Point: 00000000
Contents:
Image 0: 3562359 Bytes = 3.4 MiB
Image 1: 1650076 Bytes = 1.6 MiB
Image 2: 11016 Bytes = 10.8 KiB
Image 3: 474 Bytes = 474 Bytes
Image 4: 17936844 Bytes = 17.1 MiB
Verifying Checksum ... OK
## Loading init Ramdisk from multi component Legacy Image at ec000074 ...
## Flattened Device Tree from multi component Image at EC000074
Booting using the fdt at 0xec4f89e0
Uncompressing Multi-File Image ... OK
Loading Ramdisk to 2fe6d000, end 2ffffd9c ... OK
Loading Device Tree to 03ffa000, end 03fffb07 ... OK
setup_arch: bootmem
mpc85xx_ds_setup_arch()
arch: exit
fsl-l2ctlr ffe20000.l2-cache-controller: Entire L2 as cache, provide valid sram address and size
kennisis_cpld:led_cpld_base = f10a6000
physmap-flash.0: failed to claim resource 0
thermal_driver Fan chip is EMC2305
Initializing EMC2305 Fan Chip
starting pid 85, tty '': '/etc/init.d/rcS'
starting pid 218, tty '/dev/ttyS1': '/etc/rc.d/rc.fastpath'
Mounting /dev/mtdblock5 at /mnt/fastpath.
Mounting tmpfs at /mnt/application...done.
FASTPATH Startup Rev: 8.2.2
Select startup mode. If no selection is made within 3 seconds,
the FASTPATH Application will start automatically...
FASTPATH Startup -- Main Menu
1 - Start FASTPATH Application
2 - Display Utility Menu
Select (1, 2):
Loading image1 from /dev/mtd0
Extracting application from .stk file...done.
Loading FASTPATH...done.
Uncompressing apps.lzma
Changing lighttpd file ownership to lighttpd:lighttpd
Mounting open_websrc.sqfs onto /mnt/www/open...done
Changing restconf file ownership to lighttpd:lighttpd
Mounting restconf_websrc.sqfs onto /mnt/www/restconf...done
DMA pool size: 8388608
PCI unit 0: Dev 0xb842, Rev 0x02, Chip BCM56842_A1, Driver BCM56840_B0
SOC unit 0 attached to PCI device BCM56842_A1
Jan 7 12:02:52 0.0.0.0-1 General[fp_main_task]: bootos.c(188) 4 %% Event(0xaaaaaaaa)
started!
Jan 7 12:02:52 0.0.0.0-1 SIM[Cnfgr_Thread_]: sim_util.c(3902) 6 %% Switch was reset due to power disruption or unexpected restart.
(Unit 1)>
Applying Global configuration, please wait ...
Applying Interface configuration, please wait ...
User:admin
Password:
(Routing) >en
(Routing) #show version
Switch: 1
System Description............................. Broadcom Trident 56842 Dev System - Fixed 24*10g+configurable mix of 2x40Gb and 8x10Gb , 3.2.2.24, Linux 3.8.13-rt9-4143e257
Machine Type................................... Broadcom Trident 56842 Dev System - Fixed 24*10g+configurable mix of 2x40Gb and 8x10Gb
Machine Model.................................. BCM-56842
Serial Number.................................. CES06192820013
Maintenance Level.............................. A
Manufacturer................................... 0xbc00
Burned In MAC Address.......................... 00:E0:EC:E1:39:B7
Software Version............................... 3.2.2.24
Operating System............................... Linux 3.8.13-rt9-4143e257
Network Processing Device...................... BCM56842_A1
Additional Packages............................ BGP-4
QOS
Multicast
IPv6
Routing
Data Center
OpEN API
Prototype Open API
(Routing) #show running-config
!Current Configuration:
!
!System Description "Broadcom Trident 56842 Dev System - Fixed 24*10g+configurable mix of 2x40Gb and 8x10Gb , 3.2.2.24, Linux 3.8.13-rt9-4143e257"
!System Software Version "3.2.2.24"
!System Up Time "0 days 0 hrs 1 mins 44 secs"
!Cut-through mode is configured as disabled
!Additional Packages BGP-4,QOS,Multicast,IPv6,Routing,Data Center
!Current SNTP Synchronized Time: SNTP Client Mode Is Disabled
!
vlan database
exit
configure
line console
exit
line telnet
exit
line ssh
exit
router ospf
exit
ipv6 router ospf
exit
exit
(Routing) #show serial
Serial Port Login Timeout (minutes)............ 5
Baud Rate (bps)................................ 115200
Character Size (bits).......................... 8
Flow Control................................... Disable
Stop Bits...................................... 1
Parity......................................... none
(Routing) #show host
Host name......................................
Default domain................................. Domain name is not configured
Default domain list............................ Domain Name List is not configured
Domain Name Lookup............................. Enabled
Number of retries.............................. 2
Retry timeout period........................... 3
Name servers (Preference order)................ Name servers are not configured
DNS source interface........................... (not configured)
Configured host name-to-address mapping:
Host Addresses
------------------------ ----------------------
No host name is configured to IP address
Host Total Elapsed Type Addresses
---------------------- ------- ------- ---- --------------
No hostname is mapped to an IP address
(Routing) #show interface switchport
Packets Received Without Error................. 0
Broadcast Packets Received..................... 0
Packets Received With Error.................... 0
Packets Transmitted Without Errors............. 0
Broadcast Packets Transmitted.................. 0
Transmit Packet Errors......................... 0
Address Entries Currently in Use............... 1
VLAN Entries Currently in Use.................. 1
Time Since Counters Last Cleared............... 0 day 0 hr 8 min 18 sec
(Routing) #show terminal length
Terminal length
----------------
For Current Session............................ 24
For Serial Console............................. 24
For Telnet Sessions............................ 24
For SSH Sessions............................... 24
好評 (13,300)
差評 (16)
Line線上客服
FB粉絲團
台灣
日本
美國
